Preamp - KEPmeters https://kepmeters.com Flow Meter Displays and DPMs by KEP Mon, 19 Feb 2018 04:08:13 +0000 en-US hourly 1 https://wordpress.org/?v=6.5.2 https://kepmeters.com/wp-content/uploads/2019/08/cropped-K-site-logo-32x32.png Preamp - KEPmeters https://kepmeters.com 32 32 AMP-2 https://kepmeters.com/product/amp-2/ Sat, 17 Feb 2018 22:13:15 +0000 http://kepmeters.kep-temp.com/?post_type=product&p=1134 Dual Preamp & Signal Conditioner for Magnetic Pickups

The post AMP-2 first appeared on KEPmeters.

]]> The KEP AMP-2 is a two channel amplifier for use with magnetic pickups. It amplifies and squares the low level signals from a magnetic pickup to drive any ratemeter, totalizer or controller. The unit operates from 8.5 to 30 VDC. It has a 10K pullup resistor attached to the open collector output and sinks a minimum of 20 mA to less than 1 V from a maximum of 30 VDC. It is available in OEM (PC board only), NEMA4X enclosure or in a rugged explosion proof housing with screw terminals for easy installation. Operating temperature is -40° to 65°C.

Note: The low voltage line from the magnetic pickup to the AMP-2 should be less than 10 ft. in length, shielded and isolated from relays, solenoids or other sources of electrical noise (let the output line make the long run). If the input is too sensitive, lower the 10K input impedance by adding a 1K ohm resistor across TB1, pins 1 and 2, 4 and 5 to increase noise immunity.

The post AMP-2 first appeared on KEPmeters.

]]> AMP1-N https://kepmeters.com/product/amp1-n/ Sat, 17 Feb 2018 22:10:40 +0000 http://kepmeters.kep-temp.com/?post_type=product&p=1132 Preamplifier & Signal Conditioners for NAMUR Sensors

The post AMP1-N first appeared on KEPmeters.

]]> The KEP AMP-1-N powers and conditions the low level signals from NAMUR pickups, sensing gear teeth movement or flow, and provides a high level pulse output suitable to drive any KEP ratemeter, counter or controller.

The post AMP1-N first appeared on KEPmeters.

]]> AMP1 & AMP1-10K https://kepmeters.com/product/amp1-amp1-10k/ Sat, 17 Feb 2018 22:05:53 +0000 http://kepmeters.kep-temp.com/?post_type=product&p=1127 Preamp & Signal Conditioner for Magnetic Pickups

The post AMP1 & AMP1-10K first appeared on KEPmeters.

]]> The KEP AMP 1 amplifies the low level signals from a magnetic pickup or flow transmitter by a factor of more than a hundred times to drive any ratemeter, counter or controller. The unit uses only 30 mA and operates from 11 to 26 VDC. It has a 2.7K pullup resistor attached to the open collector output and sinks a minimum of 100 mA to less than 1 V from a maximum of 26 VDC. It is mounted in a rugged 2″ x 3″ metal housing with screw terminals for easy installation. Operating temperature is 32 to 140° F (0 to 60° C).

A special version, the AMP1-10k, is available with 10 kΩ impedance for use with turbine and paddle wheel flowmeters.

The post AMP1 & AMP1-10K first appeared on KEPmeters.

]]>